IQAN-LST analog mini-lever

Application

The IQAN-LST is a paddle style, analog mini-lever in the IQAN product group.This lever focuses on compact design, weather resistance and safety.

The LST is a small single-axis joystick 0.5 – 4.5 Vdc, intended for the proportional control of one doubleacting hydraulic function. The combination of a minilever and armrest can provide substantial ergonomic benefits. The LST can be mounted in the armrest or on the dashboard in mobile vehicles. It is easily actuated with a fingertip for good ergonomics.

The IQAN-LST is lightweight with small installation dimensions.The LST also has low, well-adapted forces designed in for ease of operation in close quarters.

The lever is covered with friction rubber on either side, to prevent the fingers from slipping and to provide a comfortable feel. Mounting screws are installed from underneath for a clean appearance of the dashboard, panel or armrest.

The IQAN-LST is designed for the outdoor environment. The electronics are potted and the cable has a choice of either a Saab sealed AMP junior-power timer connector or a Deutsch DT series transportation connector. These features combine to give the LST an IP66 rating.

The IQAN-LST is a spring centered, dual sensor device. The dual sensors provide 0.5 – 4.5 Vdc and

4.5 – 0.5 Vdc outputs which allows error checking to meet high safety requirements. All inputs and outputs are protected against short circuit to ground. It is well suited as an input device for a variety of valve drivers.

For more information please view:

BROCHURE

IQAN-LSL Analogue lever

Application

The IQAN-LSL is an analog lever in the IQAN product group. This lever focuses on compact design, weather resistance and safety.

The LSL is a single-axis joystick, 0.5 – 4.5 Vdc, intended for the proportional control of one doubleacting hydraulic function. The lever has several options including a manual neutral detent and a switch in the top of the handle. For 24V systems there are solenoid detent options at full stroke in the minus direction or both plus and minus directions. A solenoid detent at 75% in the B (minus) direction is also available. The LSL can be mounted in the armrest or on the dashboard in mobile vehicles. It has a comfortable grip and is easily actuated for good ergonomics.

The IQAN-LSL is lightweight with small installation dimensions. The ergonomic design assures a comfortable grip from several angles. Mounting screws are installed from underneath for a clean appearance of dashboard, panel or armrest.

The standard IQAN-LSL has an IP65 rating above the flange and the cable has a choice of either a Saab sealed AMP junior-power timer connector or a Deutsch DT series transportation connector.

The IQAN-LSL is a spring centered, dual sensor device. The optional switch in the top of the handle can be used to detect operator presence. The dual sensors provide 0.5 – 4.5 Vdc and 4.5 – 0.5 Vdc outputs which allows error checking to meet high safety requirements. All inputs and outputs are protected against short circuit to ground. The LSL is well suited as a control unit for a variety of valve drivers.

For more information please view:

BROCHURE

IQAN-TOC2 valve driver module

Application

The IQAN-TOC2 is a simple task oriented controller in the IQAN product group. This unit is designed for ease of setup, weather resistance, and safety.

The TOC2 is a general purpose unit that can control two bi-directional valve sections or two cartridge solenoids simultaneously. The IQAN-TOC2 communicates with a variety of input and output devices. It has current mode (current closed-loop) or PWM mode (voltage open-loop) output for valve control. The analog inputs accept signals from joysticks or potentiometers. Two digital inputs can be used to read switches.

The IQAN-TOC2 has a simple mechanical interface for calibration. With a preloaded personality from the factory, setup can be easily performed on the machine using a screwdriver. Adjustments possible include threshold, maximum output and slopes. The TOC2 may also be connected to a PC and programmed using IQANdevelop software to change the functionality of the controller. This advanced feature allows the TOC2 to be used in more demanding applications.

The housing is designed to be rugged, but light and has a sealed, automotive AMP junior-power timer connector. The IQAN-TOC2 has a membrane to prevent condensation inside the housing. This controller is designed for the outdoor environment.

The TOC2 is made using selected components and conforms to strict international requirements.

Diagnostics: If an error is detected an LED on the top of the controller flashes a sequence to indicate the nature of the error.

For more information please view:

BROCHURE

IQAN-LC6-X05 mini-coordinate joystick

Application

The IQAN-LC6-X05 is a mini-coordinate joystick that incorporates ergonomic design with ruggedness, functionality, light weight and high flexibility for mobile market applications. The unit is designed to withstand aggressive conditions in different types of mobile equipment. The LC6 has a compact ergonomic design and small dimensions make it ideal for armrest and panel mounting.

Design and function

The IQAN-LC6-X05 is designed for outdoor use. The housing and handle have potted electronics and are rated up to IP67.

The ergonomic handle has a unique, patent pending, rotary knob function that adds a fourth proportional function integrated in the handle. The design gives the user a benefit to control all joystick proportional functions without changing their grip on the handle, and makes the LC6 ideal for repetitive, precise motion control during extended periods in mobile applications. The 4th axis default fitted ring has a small diameter, however, if needed, the operator can attach a larger sized ring to provide a different grip feeling. The handle makes it ideal for applications as rototilt and articulated steering.

All proportional output signals in joystick, rocker and knob are of contactless Hall effect type with dual sensors to provide redundancy for safety and reliability. A magnet shielding technology is used to protect the joystick from external magnetic fields.

IQAN-LC6-X05 joystick redundant signals allow error checking to make it easy for the application designer to meet high safety requirements by using IQAN software. The primary signal for each axis is 10%-90% of supply voltage. The corresponding secondary signal is 90%- 10% of supply voltage. The joystick has tough base material for long life and made using selected components and conforms to strict international requirements.

For more information please view:

BROCHURE